Daily Archives: Sunday, December 20, 2015

  • Marine Hardware Experts Have Best Way to Install Seacocks

    Marine Hardware Analyst Agrees With This Being the Best Way to Install Seacocks

    Raritan Engineering Company your marine hardware specialists would like to share with you these topics we thought would be of interest to you this month regarding the best way to install seacocks.

    Your marine hardware expert’s best advice for anyone contemplating adding a through-hull fitting is don’t. Through-hulls sink boats. If you can accomplish the same thing by installing a tee-connector in an existing inlet or discharge line, you avoid boring another hole in the bottom of your boat.

    New Through-Hull

    As your boat hardware and accessories outlet we know that installing a new through-hull fitting necessitates a new hole in the hull. Always locate seacocks where they are readily accessible or you defeat the purpose of having a valve in the line. Before you drill the hole, double-check the location carefully both inside and outside the hull to make sure, for example, that inside there will be ample room to throw the handle, and outside the new fitting is not going to set up turbulence in front of your depth sounder or speed log impeller.

    Select a hole saw the size of the fitting you are installing and cut the required hole by first drilling from the outside of the marine hull until the pilot drill in the hole saw penetrates the hull, then finish the hole by drilling from the inside.

    Through-Hull Replacement

    To replace a through-hull fitting, remove the nuts from the bolts through the seacock’s mounting flange and unscrew the bolts or drive them out with a hammer and a punch. Unscrew the seacock from the through-hull-with the help of a marine pipe wrench, if necessary.

    You can find more information as well as get assistance on marine hardware supplies and a marine water heater and on how to find the best way to install a seacock at Raritan Engineering.

    Marine Hardware Adviser Gives Thumbs Up on These Suggestions

    Through-hull fittings installed with polyurethane sealant can be very difficult to remove. A length of 3/8-inch threaded rod (or a long bolt) which is a nice piece of hardware, will make the job easier. Slide a washer or a metal plate too big to pass through the fitting onto the rod and capture it with a nut. Pass the rod through the fitting from inside the boat, seating the washer flat on the fitting.

    Dry-Fit

    Once the hole is prepared, the remaining steps are identical for a new seacock or a replacement. Cut a circle of ¾-inch plywood 2 or 3 inches larger than the flange of the seacock, and bore out the center with your hole saw to form a ring.

    Because you are going to thread the through-hull into the seacock, you can discard the lock nut. Insert the new through-hull fitting from outside the marine hull, then inside slip the wooden ring in place and thread the seacock onto the through-hull.

    Tighten the two parts together. Most boatyards have a special step-wrench that grips the ears inside bronze through-hulls. A wedge of scrap hardwood will do the same job.

    With the seacock tightened snugly–not too tight–you should have plenty of threads inside the seacock, but the length of the through-hull should not prevent the base of the seacock from tightening against the plywood ring hardware. If the through-hull is too short, replace the ¾-inch thick ring with a new one cut and shaped from ½-inch plywood.

    Installation

    Insert the through-hull, put the hardware plywood ring(s) in position, and insert the mounting bolts through the hull and far enough into the plywood to prevent it from turning. If the seacock is bronze, the mounting bolts must also be bronze.

    Tighten the seacock until it seats snugly on the ring and the mounting holes are in alignment. Remove the mounting bolts and heavily coat them for an inch or so below the heads with polyurethane sealant. Reinsert them through hull, ring, and flange, and install a washer and a nut on each.

    So don’t forget these steps needed in installing a seacock. 1) New through-hull;  2) through-hull replacement;  3) dry fit;  and then 4) installation.

    Raritan Engineering your marine parts depot has more information on marine hardware such as a boat water heater and the best way to install seacocks. See our extensive line of marine products on our website.

    Via: http://raritaneng.com/marine-hardware-experts-have-best-way-to-install-seacocks/

  • Marine Hardware Expert Concurs With This Being the very best Way to Install Seacocks

    Marine Hardware Expert Concurs With This Being the very best Way to Install Seacocks

    Raritan Engineering Company your marine hardware specialists would love to discuss with you these topics we assumed would certainly be of passion to you this month relating to the very best method to mount seacocks.

    Your marine hardware professional's finest insight for any individual considering building a through-hull installation is don't. Through-hulls sink watercrafts. If you could complete the same thing by setting up a tee-connector in an existing inlet or discharge line, you prevent uninteresting another opening in all-time low of your boat.

    New Through-Hull

    Go to http://www.raritaneng.com and see your marine water heater specialists understand that mounting a new through-hull fitting demands a brand-new opening in the hull. Consistently find seacocks where they are readily easily accessible or you defeat the function of having a valve in the line. Prior to you pierce the hole, confirm the place thoroughly both within and also outside the hull making sure, for instance, that inside there will certainly be ample space to toss the manage, and also outside the new fitting is not going to establish disturbance in front of your depth sounder or speed log impeller.

    Select an opening saw the size of the suitable you are mounting and also cut the required hole by initial boring from the beyond the marine hull till the pilot drill in the hole saw passes through the hull, then complete the hole by piercing from the within.

    Through-Hull Replacement

    To change a through-hull installation, get rid of the nuts from the screws via the seacock's placing flange and unscrew the screws or generate them out with a hammer as well as a strike. Loosen the seacock from the through-hull-with the assistance of a marine monkey wrench, if essential.

    You could find even more information along with obtain support on marine water heater and also on how you can find the very best means to mount a seacock at Raritan Engineering.

    Marine Hardware Adviser Has the Following Suggestions on Installing a Seacock

    Through-hull fittings mounted with polyurethane sealer could be very challenging to get rid of. Pass the pole through the suitable from inside the boat, seating the washer level on the suitable.

    Dry-Fit

    As soon as the hole is prepared, the staying actions are identical for a brand-new seacock or a replacement. Cut a circle of 3/4-inch plyboard 2 or 3 inches larger than the flange of the seacock, and substantiated the center with your opening attended develop a ring.

    Because you are needing to thread the through-hull right into the seacock, you can discard the lock nut. Place the new through-hull fitting from outside the marine hull, after that inside slip the wooden ring in location and also thread the seacock into the through-hull.

    Tighten up the 2 components with each other. Most boatyards have a special step-wrench that grips the ears inside bronze through-hulls. A wedge of scrap hardwood will do the very same job.

    With the seacock tightened well– not also tight– you ought to have a lot of strings inside the seacock, but the length of the through-hull should not stop the base of the seacock from tightening against the plyboard ring hardware. If the through-hull is also short, replace the 3/4-inch thick ring with a brand-new one cut and also formed from 1/2-inch plyboard.

    Setup

    Place the through-hull, placed the hardware plyboard ring(s) ready, and place the placing bolts through the hull and also much sufficient right into the plywood to avoid it from transforming. If the seacock is bronze, the installing screws have to additionally be bronze.

    Tighten up the seacock up until it sittings comfortably on the ring and the installing holes remain in alignment. Get rid of the placing screws as well as greatly coat them for an inch or two listed below the heads with polyurethane sealant. Return them with hull, ring, and flange, as well as set up a washer and also a nut on each.

    So remember these steps needed in mounting a seacock. 1) New through-hull; 2) through-hull substitute; 3) completely dry fit; then 4) setup.

    Click here to see how Raritan Engineering has even more information on marine hardware, marine hot water heater, boat hot water heater as well as the very best means to install seacocks.

    Via: http://raritaneng.com/marine-hardware-experts-have-best-way-to-install-seacocks/